Case IH DH363

CaseIH Draper Head DH363

Draper Headers

 

More Acres, Less Time

  • Dual Circuit Header Drive provides more power to the knife drive and draper belts for faster cutting and better swath formation
  • All-new 40-foot draper header covers more acres in less time
  • Low-profile cutterbar cuts closer and cleaner to reduce harvest loss

Higher Throughput Capacity

  • Wider windrow/swath opening – up to 72 inches – creates smoother crop flow
  • Improved crop feeding with shallow-angled header top section
  • More consistent swath formation thanks to a two circuit hydraulic system

Handles the Toughest Conditions

  • All-new frame design with heavy-duty reel arms provides increased strength and durability
  • Center drive draper belts provide consistent crop flow through the header even in high volume crop conditions
  • Heavy-duty cutter bar system is more durable in rocky conditions and provides a clean cut in heavy wet crops

Basic Unit Notes

  • All DH3 series draper headers are not compatible with MY2013 and prior Windrowers
  • DH2 series draper headers and prior models are compatible with MY2014 Windrowers
  • Model Year 2014 Windrowers with the draper package feature twin 40 GPM header drive pumps
  • New 40 Foot Draper Head available for WD1903 and WD2303
  • Increases drive power minimizing header stalling in adverse field conditions

Maximum Control with the Hydraulic Flotation System

Allows the header to closely follow ground contours so you capture all the crop you grow. The return-to-cut feature uses cut height cylinders on each lift arm to easily return to the preset cutting height on each pass. Make this adjustment easily from the seat of the cab using the cut height control switches on the MultiFunction Propulsion Lever.

Hydraulic System

  • Two circuit hydraulic system
    • System 1 runs knife
    • System 2 runs reel and draper
  • Reel and draper circuit has a priority flow system that allows base unit to be programmed for draper and reel to sync with ground speed
  • All circuits have speed sensors for in cab monitoring

Reel Arms

  • 2" x 3" tubing for increased strength
  • Steeper attack angle for improved crop feeding and less risk of running reel tines into knife during fore/aft operation

Transport Options

Transport - 25 & 30 Ft. Headers

  • Heads are available without transport system
  • 2-wheel, removable/swing away transport system similar to DH2 Series

Transport - 35 & 40 Ft. Headers

  • Integral 4-wheel dolly transport system

DH2 Cutterbar: Enhanced Cutting Performance

  • Low-profile design, ideal for harvesting short crops
  • The large-diameter reel provides superior delivery of crops from the cutterbar to draper belts
  • Choose from five- or six-bat pickup reels with steel or plastic fingers; Pickup reels lift crop to the cutterbar in downed crop conditions
  • Durable cutterbar skid shoes (Recommended when running header close to the ground for a low cut height)
  • The hay guard fits behind the cutterbar to direct crop on top of draper belts

DH3 Cutterbar: Cutterbar Improvements for Greater Operational Efficiency

Frame

  • Tube design angled for increased strength and visibility
  • Draper angle decreased from 20 degrees to 15 degrees for improved feeding and visibility

Ground Cutting and Crop Feeding

  • Low profile bottom for close-to-ground cutting at lesser guard angle (7/8" at 2 degrees of tilt)
  • Shallow-angled top section for improved crop feeding and reel cleaning

Cutting System

  • Case IH cutting system with new raised style knife head (Shown)
  • Schumacher cutting system (Shown)
  • Case IH stub guard cutting system

Draper Deck

  • Double V-Guide drapers for double life (reversible) and edge seal to keep trash out
  • Improved deck sliding by shifting decks on UHMW blocks with added space to allow material to clean out
  • Drive rollers at inside end of drapers for increased traction

Draper Deck Modifications

  • Deck sizes standard between SSW and DSW units. Only difference being the end tin (2" wider on DSW units allowing opening to be made 4" smaller)
  • 72" to 60" adjustable center-delivery heads
  • 72" to 56" adjustable on double-swath heads
  • Rear opening can be increased to 80" by removing back panel extensions

Gauge Wheel Configuration

  • Coil spring-over-shock absorber
  • Quick adjust design
  • Provides superior ground following and float
  • Increased strength in control arm
  • New Crop dividers, with adjustable angle and interchageable ends (pipe and cone), are simple to install and reduce trampling
Make Case IH
Model DH363
Draper Header  
Cutting width, ft in (m) 36' (10.97)
Center delivery or Double-swath Center or double
Upper Cross Auger Optional
Gauge wheels Optional
Maximum angle, below horizontal, degrees 2 to 8
Weight w/ Reel, lbs (kg) 5,434 (2465)
Sickle Cutterbar  
Single or double knife Dual knife only
Knife drive SCH ProDrive, hydraulically driven
Cutting system Case IH Std or Stub; or Schumacher Easy Cut
Knife speed, strokes per minute 1400
Sickle stroke, in (mm) 3.35 (85)
Reel  
Reel description UII 6-bat single or split, or HCC 6-bat flipover
Reel fore / aft position control Standard
Reel Diameter, in (mm) np
Reel speed range, rpm 10 to 75
Draper Belts  
Belt width, in (mm) 42 (1067)
Belt speed, maximum, ft/min (m/min) 760 (232)
Double swath shift means Hydraulic
Windrow center delivery width, in (mm) 56 to 72, or 80 (1422 to 1829, or 2032)
Double swath side delivery width, in (mm) 54 to 65 (1372 to 1651)
Sales Literature  
Literature number HF-5143-13
Literature date 6/1/2013
Operators Manual  
Manual number --
Manual date --
Manufacturing status Current
First Entry Date 8/1/2013
Revision Date --

Fields with asterisks* and highlighted red are required. Please email our helpful staff with any questions or comments using the contact form.

Fields with asterisks* and highlighted red are required. Your friend will receive an email that contains a reference to this page. Please send this email only to people you know who would be interested in this information.